Lab 2 - Solutions and Spectroscopy
- To determine the concentration of a copper sulfate (CuSO4) solution, and to duplicate its concentration by two methods.
1To learn how to use a pipet properly.
2To learn how to dilute a stock solution.
3To learn how to use a spectrophotometer.
4To gain practice plotting a calibration curve and use it to determine the concentration of an unknown solution.
5To learn how to make a solution from a solid reagent.
6To learn how to make a solution by diluting a stock solution.
IntroductionA solution is a homogeneous mixture of two or more substances. Simple solutions consist of one solvent and one or more solutes. The solvent is the major liquid component of the mixture in solutions that contain one or more liquids. The most common solutions are aqueous solutions, in which water is the solvent. The concentration of a solute is the ratio of the amount of solute to the amount of solution or solvent. One of the most common ways to report concentration is in units of molarity. Molarity is defined as the number of moles of solute in one liter of solution. It has units of moles/liter (mol/L) and is given the symbol M. For example, if 1.5 moles of sodium chloride is dissolved in enough water to make 1.0 liter of solution, the concentration of sodium chloride is 1.5 M, or 1.5 mol NaCl/L of solution. This would be spoken as "1.5 molar." In order to accurately make solutions of known molarities, we must accurately determine the number of moles of the solute and the volume of the solution. Several pieces of equipment have been developed to measure accurate volumes. These include volumetric flasks, burets, pipets, and graduated cylinders. Other glassware, such as beakers and Erlenmeyer flasks, have volume markings on them, but they are less accurate. Most general chemistry students are familiar with the graduated cylinder. It is reasonably accurate and precise (± 0.5 to 1 mL depending on its size) and can be used for many measurements. However, greater accuracy and precision is often needed. Several simple devices accurate to 0.01 mL or better are in common use in laboratories. These are:
- 1. Volumetric flasks. These pear-shaped flasks are designed to contain a volume of liquid or solution which is known to 0.1 mL or better. They have a narrow neck with a single mark. Solvent is added to the mark.
- 2. Burets. These long, narrow, graduated tubes have a stopcock at the bottom. They are designed to dispense variable amounts of liquid or solution. The volume of solution in the buret is recorded before dispensing the solution and afterward. The difference between the two readings is the volume of liquid dispensed. The volume readings should be to two decimal places. Burets are most often used in titrations.
3. Pipets. Pipets, like burets, are designed to dispense a known volume of solution. There are several common types:
- a. Volumetric, or transfer, pipets have a single mark on a narrow neck. They are the most accurate pipets for delivering a known amount of liquid or solution. They are drained by gravity. Remaining traces of liquid are not forced out, e.g. by blowing on the pipet.
- b. Mohr pipets, or measuring pipets, have graduations and are used much like burets. They are not drained completely.
- c. Serological pipets are graduated and are designed to be drained completely. Most are designed to have the last traces of liquid blown out.
( 1 )
A = ε l c
εis the "molar absorptivity" (a constant unique to that solute at that wavelength) and l is the path length, or distance the light travels through the solution. To evaluate c from absorbance measurements, one measures the absorbance of several standard solutions (solutions of known concentration). A plot of A vs. c, which equation 1 shows should be linear, allows calculation of ε. In these measurements, l is held constant by using the same sample holder (or a carefully matched set of them) for all measurements. The plot of A vs. c is called a calibration curve. The concentration of any other solution can be found with the calibration curve by measuring its absorbance. There are two standard ways to make solutions of a desired concentration. First, if the solute is a solid, the appropriate amount of solid may be weighed out and then dissolved in enough solvent to make the desired amount of solution. This is often done in a volumetric flask. The accuracy and precision of the mass and volume determinations dictate the number of significant figures that can be used in reporting concentration. Usually, four significant figures are used. The second common way to make a solution is to dilute a stock solution with additional solvent. The relationship between the concentrations and volumes of the concentrated and diluted solutions is,
( 2 )
Ci Vi = Cf Vf
1MicroLab Spectrophotometer Instruction Sheet
513 × 100 mm test tubes
1test tube rack
230 mL beakers
225 mL volumetric flasks w/ stoppers
1250 mL beaker for copper waste
25 mL0.5XX M CuSO4(aq) stock solution
5 dropsCuSO4(aq) unknown solution
1 gsolid CuSO4 · 5 H2O
SafetyCuSO4 · 5 H2O is listed as toxic and an irritant. Toxic substances are hazardous to health when breathed, swallowed or in contact with the skin. An irritant may have a temporary irritating effect on skin, eyes, respiratory tract, etc. If you come in contact with the solid, you should gently brush off the affected area with a paper towel and then flush the area with water. If you come in contact with a solution of copper(II) sulfate, you should flush the affected area with water.
Waste DisposalSolutions containing copper ions must be placed in the waste bottle in the lab. Designate a "waste copper" beaker and set it aside for use during your lab. You can put the small samples of copper solution you will make in this and empty it into the waste bottle at the end of class, instead of going back and forth to the waste bottle. Always remember not to overfill the waste bottle. If your waste bottle is full, please alert your lab instructor.
Prior to ClassPlease read the following section of Lab Safety and Practices: Please read the following section in Lab Equipment: Please review the following videos: Please complete your WebAssign prelab assignment. Check your WebAssign account for due dates. Students who do not complete the WebAssign prelab assignmentare required to print and hand in the prelab worksheet.
Lab ProcedurePlease print the worksheet for this lab. You will need this sheet to record your data.
Part A: Determination of the Concentration of a Copper(II) Ion Solution
1A spectrophotometer will be set up in your work area. Make sure it is turned on and allow it to warm up.
2While the spectrophotometer is warming up, obtain two serological pipets, and set up a beaker for waste Cu2+ solution.
3Obtain about 15 mL stock Cu2+ solution. Write its exact concentration in Data Table A.
4Once the spectrophotometer is warmed up, take a blank spectrum of deionized water in a vial as described in the MicroLab spectrophotometer instructions provided in lab.
5Condition the pipet you will be using for the Cu2+ solution as shown in the Pipet video under Instrumentation and as described in the Volumetric Glassware section of the Introductory Material of this lab manual. Dispense the required volumes of Cu2+ solution (1.5 mL) and deionized water (6.5 mL) for Solution 1 into a test tube and record your volumes in Data Table A.
- • Be careful while doing this, the pipets may be tricky to handle at first.
- • Record volumes to 0.01 mL with some uncertainty in the last digit.
6Stopper the test tube and mix the solution well by inverting a couple of times.
7To condition your vial, carefully pour a small amount of the solution you just prepared into a vial and pour it out to waste.
8Refill the vial with solution and take an absorbance spectrum. Identify the wavelength of maximum absorbance near 630 nm. Record the wavelength and absorbance at this wavelength in Data Table A. Absorbance values are reported to the 0.0001. For all remaining absorbance measurements in this experiment, be sure to use the same wavelength you have identified as the maximum.
Table A: Calibration Curve of Cu2+ Solutions and Unknown
9Record the concentration of Cu2+ in Solution 1 in Data Table A .
Question 1: What is the concentration of Cu2+ in Solution 1 that you prepared? Show your calculations neatly.
10Retain the sample in the vial until you have completed your calibration plot. Students often choose to label a sheet of paper with positions 1, 2, 3 and 4, placing each vial on the appropriate position.
11Following steps 5 - 10, prepare Solutions 2 - 4, measure their absorbances and calculate the Cu2+ concentration in each. Record all of your absorbances and concentrations in Data Table A. Record these in Data Table A. Do not close the MicroLab file, as this calibration curve will be used to determine the concentrations in Part B.
Question 2: Would you predict the absorbance of solution 2 to be greater or less than that of solution 1? Why?
12The MicroLab software will plot the absorbance of the Cu2+ solutions that you made as a function of their concentrations. The trendline and R2 value are displayed. If your plot is linear with an R2 value of 0.9 or greater, continue the experiment. If your R2 value is low, consult with your lab instructor.
13Safely dispose of the calibration solutions in your copper waste beaker.
14Obtain a couple of milliliters of unknown solution and record the number of your solution in Data Table A.
15Condition a vial with the unknown Cu2+ solution and refill with unknown Cu2+ solution. Measure the absorbance of the unknown Cu2+ solution as an unknown sample, not part of the calibration plot, and record it in Data Table A.
Question 3: What is the concentration of Cu2+ in your unknown solution? Show your calculations neatly. Record this concentration in Data Table A.
Part B: Preparation of a Copper(II) Ion Solution from Solid CuSO4 · 5 H2O
Question 4: You desire to make a copper(II) solution at the same concentration as the unknown you just determined in Part A. How many grams of CuSO4 · 5 H2O are required to make 25.00 mL of this solution? Show your calculations neatly. Record the result as the target mass in Data Table B.
Table B: Preparation of a Cu2+ Solution from solid CuSO4 · 5 H2O
1Carefully weigh the desired amount of CuSO4 · 5 H2O on a weighing paper or in a small beaker as shown in the Analytical Balance video under Instrumentation and as described in the Analytical Balance section of the Introductory Material of this lab manual. Record the exact amount that you used in Data Table B.
2Transfer the CuSO4 · 5 H2O into a 25.00 mL volumetric flask and dilute to the mark with deionized water as shown in the Volumetric Flask video under Instrumentation and described in the Volumetric Glassware section of in the Introductory Material of this lab manual.
3After the solution is well mixed, condition a vial with it. Then refill the vial, measure and record the absorbance of your solution nm in Data Table B.
Question 5: Comment on how the absorbance of your solution made from solid compares to the unknown solution's absorbance in Part A. Do you expect them to be the same? Why or why not?
Part C: Preparation of a Copper(II) Ion Solution by Dilution of a Stock CuSO4 Solution.
1Record the exact concentration of the stock copper(II) solution in Data Table C.
Table C: Preparation of a Cu2+ Solution from stock Cu2+ solution
Question 6: You desire to make a copper(II) solution at the same concentration as the unknown you determined in Part A. How many mL of the copper(II) stock solution are required to make 25.00 mL of this solution? Show your calculations neatly. Record the result as the target volume in Data Table C.
2In a small, clean beaker, obtain a little more of the stock copper(II) solution than you calculated in Question 6.
3First condition a serological pipet, then use it to transfer the volume of copper(II) solution you calculated into a 25.00 mL volumetric flask. Record the exact amount that you transferred in Data Table C. Dilute to the mark with deionized water.
4After the solution is well mixed, condition a vial with it. Then refill the vial, measure and record the absorbance of your solution in Data Table C.
Question 7: Comment on how the absorbance of your solution made by dilution of a stock compares to the unknown solution's absorbance in Part A. Do you expect them to be the same? Why or why not?
5When you are finished taking measurements, collect all your copper solution waste and place it in the waste bottle in the lab, making sure not to overfill it. Rinse and dry all your glassware with water and return it to the set-up area where you found it. Close the MicroLab software.
6Remember to show your TA your calibration curve and measured [Cu2+] concentration of your solutions for Part B and C. Your TA will manually grade the results and enter your score into WebAssign.
7Before leaving, enter your results in the In-Lab assignment. If all results are scored as correct, log out. If not all results are correct, try to find the error or consult with your lab instructor. When all results are correct, note them and log out of WebAssign. The In-Lab assignment must be completed by the end of the lab period. If additional time is required, please consult with your lab instructor.